Baso GM7000 Series Multi-function Gas Control Valve Instrukcja Użytkownika Pobierz pdf

Installation Instructions GM-7000

Issue Date November 9, 2012

Part No. BASO-INS-GM7000, Rev. F www.baso.com

GM-7000 Series CE Approved Gas Control Valve

Installation

IMPORTANT: These instructions are intended as a

guide for qualified personnel installing or servicing

BASO Gas Products. Carefully follow all instructions

in this bulletin and all instructions on the appliance.

Limit repairs, adjustments, and servicing to the

operations listed in this bulletin or on the appliance.

WARNING: Risk of Fire or Explosion.

The system must meet all applicable local, national,

and regional regulations. Improper installation may

cause gas leaks, explosions, property damage, and

injuries.

WARNING: Risk of Fire or Explosion.

To prevent leakage of upstream gas, shut off the gas

supply at the main manual shutoff valve before

installing or servicing the GM-7000 valve. Failure to

shut off the gas supply can result in the release of

gas during installation or servicing, which can lead to

an explosion or fire, and may result in severe

personal injury or death.

Mounting

CAUTION: Risk of Equipment Damage.

To prevent damage to the valve when mounting to

pipework, do not use a wrench on any surface other

than the casting flats provided at the inlet and outlet

ends of the valve body.

To install the GM-7000 valve:

1. Shut off power to the appliance.

2. Shut off the gas at the main manual shutoff valve.

3. Label each wire with the correct terminal

designation prior to disconnection.

4. Compare the voltage on the valve with the power

source voltage to ensure the correct unit is being

installed.

5. Mount the valve. The GM-7000 valve may be

mounted on a horizontal manifold with the

magnetic operators (solenoid coils) pointed up

(vertical) or in any position not exceeding 90°

from the vertical (Figure 1). The valve may also

be mounted on a vertical manifold in any position

around its axis. Do not install the solenoid coils

upside

down. Install vertically wherever possible.

6. If you desire to measure the outlet pressure, use

the bottom cast pressure test fitting.

90° Maximum

from Vertical

90° Maximum

from Vertical

Limited Horizontal and Vertical

Vertical mounting may

be 360º around its axis

with the gas flow either

up or down, but always in

the direction of the arrow.

Figure 1: GM-7000 Mounting Positions

7. Install the valve on the manifold; ensure the gas

flows through the valve body in the direction

indicated by the arrow on the body. If the valve is

installed with the gas flow in the opposite

direction of the arrow, leakage can occur.

1 2 3 4 5 6

Podsumowanie treści

Strona 1 - Mounting

Strona 2 - Connection

2 GM-7000 Series CE Approved Gas Control Valve Installation Instructions Note: If installing a valve with threaded connections, use an approved

Strona 3

GM-7000 Series CE Approved Gas Control Valve Installation Instructions 3 LNLNTo Main SolenoidTo Pilot SolenoidL2N2N1L1Coil 2MainValveCoil 1Pilot

Strona 4 - Repairs and Replacement

4 GM-7000 Series CE Approved Gas Control Valve Installation Instructions Wiring ! CAUTION: Risk of Electric Shock. Disconnect power supply bef

Strona 5 - Technical Specifications

GM-7000 Series CE Approved Gas Control Valve Installation Instructions 5 Technical Specifications Product GM-7000 Series CE Approved Gas Control

Strona 6

6 GM-7000 Series CE Approved Gas Control Valve Installation Instructions Technical Specifications (continued) Agency Listings CSA (AGA/CGA) Certi

Komentarze do niniejszej Instrukcji

Brak uwag

Baso GM7000 Series Multi-function Gas Control Valve Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Baso GM7000 Series Multi-function Gas Control Valve. BASO GM7000 Series Multi-function Gas Control Valve User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Baso GM7000 Series Multi-function Gas Control Valve